Our products

Products

>

Other products

>

Article under construction

Article under construction

Ø 7 - 15 working days (*)


Schneider Electric PRA90043


12.20 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A1113

	Altivar - terminal graphique de base déportable BASIS DISPLAY Terminale display HMI - 128 x 64 pixel - IP21 This plain text terminal is an option for variable speed drives of Altivar range. It is a dialogue option for the variable speed drive. Its protection index is IP21. The plain text display terminal can be connected and mounted on the front of the drive. Its maximum operating temperature is 50 °C. It provides a pixel resolution of 128 x 64 pixels. It weighs 200g. It is used to control, adjust, and configure the drive, display current values (motor, I/O, and machine data), store and download configurations (several configurations can be stored) and duplicate the configuration of one to another drive. A remote mounting kit for mounting on enclosure door with IP43 degree of protection is available as accessory, to be ordered separately.
158.80 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A31101

	Altivar - terminal télécommandé - pour moteur pas à pas - pour ATV31 Dezentrales Bedienterminal, f. Schrittmotorverstärker, Frequenzumrichter ATV31 Terminale remoto - Per azionamento motore passo-passo, az. vel. var - ATV31 This 4-digit display terminal is an option for variable speed drives of Altivar range and servo drives of Lexium range. It is a dialogue option for the variable speed drive or servo drive. Its protection index is IP65. This terminal can be mounted on an enclosure door. It is supplied with a cordset equipped with 2 connectors, a seal and screws. It weighs 380g. It is used to show the drive states, faults and parameter values of the drive. The navigation buttons are used to navigate through the menus, modify values and enter the main settings.
310.80 CHF

Ø 7 - 15 working days (*)


Schneider Electric VW3A3401

	Altivar - carte d'interface de codeur - avec sorties diff. compat. RS422 - 5Vcc Encoder-Interfacekarte mit RS422-kompatiblen Differenzausgängen, 5 V DC Scheda Encoder RS422 5V This encoder interface card can be used for Flux Vector Control operation with sensor for asynchronous motors. It can also be used for Vector Control operation with speed feedback for synchronous motors. It improves drive performance irrespective of the motor load state. It is compatible with RS 422 differential outputs encoder technology. This card is simple to install and remove, it is inserted in a dedicated slot of the variable speed drive. It is protected against encoder supply short circuits and overloads. It is compatible with Altivar 61 and Altivar 71.
261.90 CHF

Ø 7 - 15 working days (*)


Schneider Electric VW3A3407

	Altivar - carte d'interface de codeur - avec sorties push-pull - 24Vcc Encoder-Interfacekarte mit Gegentakt-Ausgängen (push-pull), 24 V DC Scheda Encoder push pull 24V This encoder interface card can be used for Flux Vector Control operation with sensor for asynchronous motors. It can also be used for Vector Control operation with speed feedback for synchronous motors. It improves drive performance irrespective of the motor load state. It is compatible with push-pull outputs encoder technology. This card is simple to install and remove, it is inserted in a dedicated slot of the variable speed drive. It is protected against encoder supply short circuits and overloads. It is compatible with Altivar 61 and Altivar 71.
261.90 CHF

Ø 7 - 15 working days (*)


Schneider Electric VW3A3409

	Altivar - carte d'interface de codeur - universel - 5V Universal-Encoder-Interfacekarte, 5 V Scheda Encoder universale This universal encoder interface card is an option for variable speed drives of Altivar range. It is compatible with Altivar 71. It improves drive performance irrespective of the motor load state, zero speed torque, accurate speed regulation, torque accuracy, shorter response times on a torque surge, improved dynamic performance in transient state. It is protected against short circuits and overloads. It weighs 200g. It is used for Flux Vector Control operation with sensor (FVC mode) for asynchronous motors, or for Vector Control operation with speed feedback (FSY mode) for synchronous motors. It is inserted in a dedicated slot of the drive.
261.90 CHF

Ø 7 - 15 working days (*)


Schneider Electric VW3A3420

	Altivar - interface codeur logique - 5/12V Digital-Encoder-Schnittstellenmodul 5/12 V Scheda encoder digitale ATV340/ATV900 - 5/12 V This digital encoder interface module is an option for variable speed drives of Altivar range. It is compatible with Altivar Machine ATV340 and Altivar Process ATV900 drives. It improves drive performance irrespective of the motor load state, zero speed torque, accurate speed regulation, torque accuracy, shorter response times on a torque surge, improved dynamic performance in transient state. It is protected against short circuits and overloads. It weighs 150g. It is used for Flux Vector Control operation with sensor (FVC mode) for asynchronous motors, or for Vector Control operation with speed feedback (FSY mode) for synchronous motors. It is inserted in a dedicated slot of the drive.
367.90 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A3422

	MODULE CODEUR ANALOGIQUE CARTE ELECTRONI Analog-Encoder-Schnittstellenmodul Scheda encoder analogica ATV340/ATV900 This analog encoder interface module can be used for Flux Vector Control operation with sensor for asynchronous motors. It can also be used for Vector Control operation with speed feedback for synchronous motors. It improves drive performance irrespective of the motor load state. This module is inserted in a dedicated slot of the variable speed drive. It is protected against encoder supply short circuits and overloads. It is compatible with Altivar Process ATV900 and Modular, and Altivar Machine ATV340. It has 1 female high density SUB-D 15 connector.
367.90 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A3423

	MODULE INTERFACE RESOLVEU R CARTE ELECTRO Schnittstellenmodul für Encoder mit Istwertrückführung Scheda resolver ATV340/ATV900 This resolver encoder interface module can be used for Flux Vector Control operation with sensor for asynchronous motors. It can also be used for Vector Control operation with speed feedback for synchronous motors. It improves drive performance irrespective of the motor load state. This module is inserted in a dedicated slot of the variable speed drive. It is protected against encoder supply short circuits and overloads. It is compatible with Altivar Process ATV900 and Modular, and Altivar Machine ATV340. It has 1 female SUB-D 9 connector.
367.90 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A3424

	Altivar - option codeur sortie Push Pull HTL-Encoder-Schnittstellenmodul Scheda encoder HTL 12/15/24V This HTL encoder interface module is an option for variable speed drives of Altivar range. It is compatible with Altivar Machine ATV340 and Altivar Process ATV900 drives. It improves drive performance irrespective of the motor load state, zero speed torque, accurate speed regulation, torque accuracy, shorter response times on a torque surge, improved dynamic performance in transient state. It is protected against short circuits and overloads. It weighs 150g. It is used for Flux Vector Control operation with sensor (FVC mode) for asynchronous motors, or for Vector Control operation with speed feedback (FSY mode) for synchronous motors. It is inserted in a dedicated slot of the drive.
367.90 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A4555

	Altivar - inductance de ligne - 0,5mH - 60A - pour variateur de vitesse Netzdrossel, 0,5mH, 60A, für Frequenzumrichter Induttanza di linea - 0,5 mH - 60 A This line choke is an option for variable speed drives of Altivar range. Its rated current is equal to 60A. It provides improved protection against overvoltages on the line supply and contributes to reduce harmonic distortion of the current produced by the drive. Its protection index is IP00. It has an inductance value of 0.5mH. It weighs 11kg and its dimensions are, 180mm wide, 210mm high, 165mm deep. Its use is particularly recommended in case of close connection of several drives in parallel, line supply with significant disturbance from other equipment (interference, overvoltages), line supply with voltage imbalance between phases.
980.90 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A4556

	Altivar - inductance de ligne - 0,3mH - 100A - pour variateur de vitesse Netzdrossel, 0,3mH, 100A, für Frequenzumrichter Induttanza di linea - 0,3 mH - 100 A This line choke is an option for variable speed drives of Altivar range. Its rated current is equal to 107A. It provides improved protection against overvoltages on the line supply and contributes to reduce harmonic distortion of the current produced by the drive. Its protection index is IP00. It has an inductance value of 0.3mH. It weighs 16kg and its dimensions are, 270mm wide, 210mm high, 180mm deep. Its use is particularly recommended in case of close connection of several drives in parallel, line supply with significant disturbance from other equipment (interference, overvoltages), line supply with voltage imbalance between phases.
1210.80 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A5104

	Altivar - inductance moteur - 215A - pour variateur de vitesse - lot de 3 Motordrossel, 215A, für Frequenzumrichter- Verpackungseinheit: 3 Stck. Induttanza motore 215A (x3) This motor choke is an option for variable speed drives of Altivar 61 / Altivar 71 range. Its rated current equal to 215A. It is used as an output filter (between drive output and motor) and enables your variable speed drive to run with motor cables longer than the maximum permitted lengths. Its protection index is IP00. It weighs 15.5kg. It is used to limit overvoltages at the motor terminals, filter interference and reduce motor earth leakage current. It is sold in indivisible quantity of 3.
1037.60 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A5106

	Altivar - inductance moteur - 481A - pour variateur vitesse ATV61/ATV71 - IP00 Motordrossel, 481A, für Frequenzumrichter ATV61/ATV71, IP00 Induttanza motore 481A (X3) This motor choke is an option for variable speed drives of Altivar 61 / Altivar 71 range. Its rated current equal to 481A. It is used as an output filter (between drive output and motor) and enables your variable speed drive to run with motor cables longer than the maximum permitted lengths. Its protection index is IP00. It weighs 58 kg. It is used to limit overvoltages at the motor terminals, filter interference and reduce motor earth leakage current. It is sold in indivisible quantity of 3.
3252.50 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A5209

	Altivar - filtre sinus - 400A - pour variateur de vitesse Sinusfilter, 400A, für Frequenzumrichter Filtro sinus per variatore di velocità 400A This sinus filter is an option for variable speed drives of Altivar range. Its rated current is equal to 400A. It is used as an output filter (between drive output and motor) and enables your variable speed drive to run with motor cables longer than the maximum permitted lengths. Its protection index is IP00. It weighs 190kg. It is used for applications requiring long cable runs, motors connected in parallel, submersible pumps sensitive to dv/dt, an intermediate transformer between the drive and the motor.
16134.23 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7730

	Altivar - résistance de freinage - 100ohms - 0,1kW - IP20 Bremswiderstand, 100Ohm, 0,1 kW, IP20 Resistenza di frenatura - 100 ohms - 0,1 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 100Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 1.5kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
143.00 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7731

	Altivar - résistance de freinage - 60ohms - 0,16kW - IP20 Bremswiderstand, 60Ohm, 0,16 kW, IP20 Resistenza di frenatura - 60 ohm - 0,16 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 60Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 2kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
161.10 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7732

	Altivar - résistance de freinage - 28ohms - 0,3kW - IP20 Bremswiderstand, 28Ohm, 0,3 kW, IP20 Resistenza di frenatura - 28 ohm - 0.3 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 28Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 3kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
238.70 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7733

	Altivar - résistance de freinage - 16ohms - 1,1kW - IP20 Bremswiderstand, 16Ohm, 1,1 kW, IP20 Resistenza di frenatura - 16 ohm - 1,1 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 16Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 4kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
449.20 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7741

	Altivar - résistance de freinage - 60ohms - 0,5kW - IP20 Bremswiderstand, 60Ohm, 0,5 kW, IP20 Resistenza di frenatura - 60 ohm - 0,5 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 60Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 4.5kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
681.80 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7742

	Altivar - résistance de freinage - 28ohms - 1,1kW - IP20 Bremswiderstand, 28Ohm, 1,1 kW, IP20 Resistenza di frenatura - 28 ohm - 1,1 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 28Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 4kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
1020.30 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7743

	Altivar - résistance de freinage - 16ohms - 2,2kW - IP20 Bremswiderstand, 16Ohm, 2,2 kW, IP20 Resistenza di frenatura - 16 ohm - 2,2 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 16Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 7kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
1379.30 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7744

	Altivar - résistance de freinage - 10ohms - 3,4kW - IP20 Bremswiderstand, 10Ohm, 3,4 kW, IP20 Resistenza di frenatura - 10 ohm - 3,4 kW - IP20 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 10Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP20. It weighs 11.5kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
1443.90 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7746

	Altivar - résistance de freinage - 5ohms - 6,9kW - IP23 Bremswiderstand, 5Ohm, 6,9 kW, IP23 Resistenza di frenatura - 5 ohm - 6,9 kW - IP23 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 5Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP23. It weighs 27kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
3107.60 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7752

	Altivar - résistance de freinage - 28ohms - 5,1kW - IP23 Bremswiderstand, 28Ohm, 5,1 kW, IP23 Resistenza di frenatura - 28 ohm - 5,1 kW - IP23 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 28Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP23. It weighs 25kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
1358.80 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7753

	Altivar - résistance de freinage - 16ohms - 14kW - IP23 Bremswiderstand, 16Ohm, 14 kW, IP23 Resistenza di frenatura - 16 ohm - 14 kW - IP23 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 16Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP23. It weighs 47kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
2706.60 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7754

	Altivar - résistance de freinage - 10ohms - 19kW - IP23 Bremswiderstand, 10Ohm, 19 kW, IP23 Resistenza di frenatura - 10 ohm - 19 kW - IP23 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 10Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP23. It weighs 67kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
4733.10 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7755

	Altivar - résistance de freinage - 8ohms - 25kW - IP23 Bremswiderstand, 8Ohm, 25 kW, IP23 Resistenza di frenatura - 8 ohm - 25 kW - IP23 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 8Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP23. It weighs 86kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
5849.30 CHF

Ø 3 - 7 working days (*)


Schneider Electric VW3A7756

	Altivar - résistance de freinage - 5ohms - 32kW - IP23 Bremswiderstand, 5Ohm, 32 kW, IP23 Resistenza di frenatura - 5 ohm - 32 kW - IP23 This braking resistor is an option for variable speed drives of Altivar range. It has an Ohmic value of 5Ohms at 20°C. This braking resistor allows your variable speed drive to operate while braking to a standstill, by dissipating the braking energy and enables maximum transient braking torque. Its protection index is IP23. It weighs 126kg. This resistor is designed to be mounted on the outside of the enclosure, but should not inhibit natural cooling, air inlets and outlets must not be obstructed in any way.
9502.68 CHF

ABOUT US

PRODUCTS

SUPPORT AND SERVICE

OUR PARTNER

Company
Your requirements
Contact
Vacancies

+41 (0)56 222 38 18
mailbox@sentronic.com

Sensors
Automation
Components
Distribution, Wiring
Ex Zone

ACTUAL
News
OEM Login Request

Call orders
More than 30 years of experience
Your requirements, our solutions
Testing units

Sensor KnowHow

Software Download

Available second source solutions

Crouzet
Panasonic
Telemecanique
Schneider Electric
Sensata Technologies
Kimo Instruments
Quintex
M-System

(*) Due to worldwide resource problems, there may be deviations in the stated delivery times!